Tevs 98 B13 Sentra LecPS VE

[Sunny]

Finally got a newer 98 Chassis which came standard with a Carb GA13DS, bought it in the southern part of the Philippines, drove about 6 hours North and finally made it to Baguio around 1pm

Arrived at the shop and we get to work

we pressurize/Degrease/Soap/Scrub out and underwash everything to take out years of crud and mud/dirt


Fit the GTS 1 bumper after washing off the front end as well


broke down all suspension and brake components:

Went through the entire suspension assembly and replaced components, Preload upon tightening all Components after assembly

Front
1. Arm Balljoints using 555
2. Steering rack clamp bushings
3. Front stabilizer bushings
4. Tie Rod Ends 555
5. Rack Ends 555
6. Installed Bilstein HD Yellow's with the B&G Springs using oem TopMounts and Bearings
7. Installed Front KSB Underbrace (its the pinoy copy of Shigspeed)
8. Installed ES Engine Mounts on Torque Set (Front and Rear)
9. New Stabilizer End Links came with car that the owner never installed


Rear
1. Stabilizer Bushings
2. Installed Bilstein HD Yellow's with the B&G Springs using oem TopMounts and Bearings
3. Install Rear Bar
4. New Stabilizer End Links came with car


Brakes = AD22VF Fronts and A7's Rear
1. Checked and Cleaned All Pistons and Sliders, cleaned and regreased sliders (retightened Caliper Brackets)
2. Checked All Pads front and rear with shims
3. Installed APP Stainless Steel Brakes
4. Full bleed Removed all Old Brake Fluid and air pockets

[Sunny]

Nonstop work for about 2 days

oem nissan vc gasket finally arrived, china replacements leak


Copy header


Shigspeed Copy underbrace


2.5 inch exhaust piping (mild Steel)

[Sunny]

Next Up was replacing the Leaking Valve Cover Gasket and Accesory Belts

We Used a Valve Cover Gasket meant for the SR20DE Powered Altima, Perfect Fit, since we had the VC removed, checked all cam lobes and they are smooth as well as the head assembly

the replacement vc eventually leaked, now using oem Nissan Altima Sr20DE VC gasket

a Quick Engine Flush and Regular Oil Changes will eventually remove the oil residue


purchase GATES Belts to replace the cracked PITWORK Accessory belts that came with the Engine, here are the part numbers, the thicker belt for the AC Compressor and Alternator was supposed to be 1030, as the store only had 1040, it worked and tensioned fine

oem Pitwork belts that came with the engine are
4PK855
6PK1030

these are all that was available local and they work fine

[Sunny]

Used a GA16DE ecu holder bracket for the SR20VE A/T ECU



Removed the carpet and cleaned all panels , removed the fabric from the door panels and used Mark-V Interior Cleaner (Klenzol) to remove the adhesive residue. as well as all sidings, panels and Dashboard, easier to remove and do wiring with all the stuff out of the way.

after assembly, we installed the Fidanza Short Shift Kit, Signal Auto Shiftknob, Momo Corsa SW and Hub, Bride Zeta 1 Bucket seat with Bride Slider and Bracket.

[Sunny]

threw some surplus used JDM parts that we found at the JDM importers.

we got a long way to go, and waiting on more parts, for now it runs fine

[Mad_G20]

Nice proggres car looks really good, keep up the good work

[j-tek]

wow, shes in mint condi. no rust, original paint? subscribing

[Crazy4myP10]

Nice work pare!

[Cesarin_se-r]

Nice b13 Tevs!

[Teachmehowto20]

looks good,

[Sunny]

JC Racing Silicone radiator Hoses Just arrived, got em for around $60 for the pair



JC Racing Part Numbers


angle of lower radiator hose


Purchase 4 of the Best Stainless Clamps you can find, in this case the best we can find are GATES Clamps (Made in the U.S.A) at 60 pesos each




dont forget to insert and slide over a couple of Gates Clamps prior to sliding the Silicone Hose over your Filler Hose as well as in the right orientation, easier to tighten the 8mm clamps

[Sunny]

wow, shes in mint condi. no rust, original paint? subscribing

Original Paint and No Rust, Paint Fading on the roof and trunk, i think i will keep it unpainted for the next few years or until i'm done sorting out everything

[Kidcaffeine]

is that a BE engine?

[j-tek]

Can you source me those clear/see through rad hoses? Salamat

[p10der]

http://www.clearrad.com/clear_radiatorhose.htm

[Myx]

Hey, I remember you from Nissanbayan. Haha! too bad that site went down and nobody took care of it.

how's everything going?

[CoZZm0]

Do your Bilstein HD Yellow fronts have a part number left on them ?

[Sunny]

kidcaffeine = nah, its a GA13DS

j-tek = check this out, Clear Rad Products Phone: (562) 594-3892 USA (866) 629-1024, looks like a SoCal Area Code, i'm in P.I. Meng

myx = Glad you remember me meng, i cant even remember most of the peeps anymore, Mike Black may up NB this year, Chuck kim aka Monk (passed away last year = he had all the info for NB Domain and Board), Mark wrecked his DET altima, 2 forums soaked up most of the peeps from NB, Sentra Club Philippines and Club Nissan Sentra

coZZmo = i will search for them bud, i saved the part number somewhere, these are HD Yellow's Cartridges meant for the Corolla AE101 fitted into emptied out B13 Strut Casings, got em from a Distributor here called Speedlab

[Sunny]

MAF (Mass Air Flow Meter pigtail), CAS (Cam angle Sensor), VVL Solenoid...etc. harness

[devious_se]

Holy fuck thats a lot of wires......... man u must be patient. Looks like its comming along nicely. I miss my b13 ser