Infiniti G20 Nissan Primera Forum banner

1 - 20 of 638 Posts

·
Pining for "DMSentra"
Joined
·
5,558 Posts
Discussion Starter #1 (Edited)
F/S P10-11 90a Polyu motor, trans, and xmember mount inserts

Yes, that's right.. finally someone (me, Loren, LoCo, [email protected] = PAYPAL ) is making direct press in poly motor mount inserts. These inserts are being offered in a few options for all Infiniti G20's.

First is the inserts with sleeves on their own. The cost for this option is:
$60 for each crossmember(between the crossmember and engine/trans, the small ones) insert
$75 for each trans(drivers side upper) and motor(passenger side upper) insert.
$170 for a set of 3 incl. Pass side, Trans side, and one xmmbr (This is for P10 as I am not making the dogbone replacement front lower mount)
$220 for a set of 4 incl. Pass side, Trans side, and two xmmbr(This is for P11, including both round xmember mounts, or P10 when you're doing the P11 xmember swap to run 4 mounts in your P10)


The second option is buying the inserts and having them pressed into your core mounts. This option would cost the same for the inserts, but there will be a small fee for that pressing service.
The last option will include buying complete units from me on an exchange/core charge basis. Pay for the inserts, pressing fee, and core charge(s) up front and then send cores back within 2 weeks when you receive the package to get your core charge back.

$15 each for pressing in less than a set.
$55 for pressing in a set.
$35 for xmember mount core charge.
$70 for motor or trans mount core charge.


Gentlemen, please include exactly what mounts you are paying for. I need the year and which mounts to fit that year(full set of 3 for p10, 4 for p11, or which singles). I can't send what you want when you don't tell me, and I really try not to rely on memory because it's too easy to make mistakes. Thanks.

One thing I want to mention about getting complete mounts from me instead of sending in your cores. I can only work with how nice the cores are that I'm sent.

I ship these by printing the shipping label with PayPal. Include your correct shipping address in your PayPal and send funds as "payment" option. Not doing this increases the chance of shipping problems. Putting the address in the notes window will probably not give you the end result you want.
Shipping, insurance, delivery confirmation, and PayPal fees will all be included for $25 for each set, and less for singles, more outside the USPS Flat Rate shipping area.

So, pricing for full sets, pressed into my cores, shipped and all, buying them outright, is $440 for p10 and $525 for p11.


Here is a couple sample pics of a xmember mount insert, and assembly.





Full P11 set ready to install



This pic is from Happynole Joe, notice he has my crossmember bushings installed also.



PayPal is [email protected]. In the note section on PayPal I'll need to know what mounts you want.

Any questions, that is also my email of course, or pm me here, or post here, or catch me in chat, or...
 

·
Registered
Joined
·
12,424 Posts
Sold!

Add yourself to the list. This is for Those who have PAID

1) snickers (p10 3-set) $220
2)
3)
4)
5)
6)
7)
8)
9)
10)
 

·
Administrator
Joined
·
5,071 Posts
Damn, I already purchased the B15 prothanes (which will require work on my side..) if not I WOULD be in on this!
 

·
Registered
Joined
·
783 Posts
I got three Nylon engine mounts done by Loren and he did some fine work at a reasonable price and now has offered his amazing work to everyone here on Gnet.

Take this up, people!
 

·
Registered
Joined
·
165 Posts
This is awesome! Thanks!

Just to clarify somethings.

Say I wanted a set of 4 (front+Rear+Tranny+Passenger) for a 00+ 5spd P11 already pressed in and ready to go....

i would have to pay 300 (260 intro price) + 40 (pressing fee) + ? (core charge). And when i get your mounts, i return my old mounts to you and you would reimburse the core charge back to me?
 

·
Questioning Answers
Joined
·
6,853 Posts
lorn. not to jimmy uo this thread...but would you do me trans & pass mount in nylon...PM me...ill delete after...jjst to not cludder this thread up (i onlly need the mounts, ill press them in)
 

·
Registered
Joined
·
869 Posts
Very nice!!

I am in desperate need of a front mm, mine is torn to shreds.
 

·
Registered
Joined
·
219 Posts
How are these compared (stiffness) to the energy suspension prothane mounts for the B13?
And these are also offered for P11 right?
 

·
Registered
Joined
·
219 Posts
I don't have prothanes so don't know first hand, but have been told by a very reputable source they are stiffer and hold up to significantly harsher conditions.

thanks for the quick response. So which one is stiffer? The B13 energy suspension prothane are stiffer than the one you are making?
And you are also making this for P11, correct?

thanks again!
 
1 - 20 of 638 Posts
Top